HUB MODULE DISTR. BOX

IMA MODULE-T1/E1 ATM CR clei This module provides the Inverse Multiplexing for ATM capability for the T1/E1 ATM Cell Relay interface cards (90-6351-0x). The module supports either ATM Forum IMA v1.0 or v1.1 through separate software loads. This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

INTEG CALLP/PNNI CARD-2 R4.3 This card provides the functionality of a R4.3 Control Card-2, a R4.3 CallP Cad-2 and a R4.3 PNNI Card-2, all combined on a single card. One card is required for non-redundant operation, and two cards for redundancy per 36170 system. This card must be installed in Contron Card slots only, and cannot be used in systems that have also been configured with CallP-2 Cards or PNNI-2 Routing cards. Node management, alarm, and timing terminations required a control card interconnect panel (CCIP). One CCIP serves both active and redundant integrated control cards. There are two variants of CCIP for US Telco (90-2295-x1) and International (90-2295-x2) requirements. This card is delivered with R4.3 software. Note that this card uses the Processor Module, and that the enhanced Processor Module (ePM) is required to upgrade to R5.0. Consequently, it is recommended that 90-6226-07 or 90-6226-09 be used instead of this part.

INTEG CALLP/PNNI CARD-2 W/ EPM R4.3 clei This card provides the functionality of a R4.3 Control Card, a R4.3 CallP Card-2 and a R4.3 PNNI Card-2, all combined on a single card. One card is required for non-redundant operation, and two cards for redundancy per 7470 system. This card must be installed in Control Card slots only, and cannot be used in systems that have been configured with CallP-2 Cards or PNNI-2 Routing cards. Node management, alarm, and timing terminations require a control card interconnect panel (CCIP). One CCIP serves both active and redundant integrated control cards. There are two variants of CCIP for US Telco (90-2295-x1) and International (90-2295-x2) requirements. This card is delivered with R4.3 software, and with an enhanced Processor Module (ePM), and with a NAND-based 256MB memory card. Note that previous to this note, all control cards were shipped wih NOR-based memory cards. The software loadset required for this card is documented in Field Notice FN1867. This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

INTEG CALLP/PNNI CARD-2 W/ EPM R5.0 This card provides the functionality of a Control Card, a CallP Card-2 and a PNNI Card-2, all combined on a single card. Two cardsare required for redundancy per 7470 system. This card must be installed in Control Card slots only, and cannot be used in systems that have been configured with CallP-2 Cards or PNNI-2 Routing cards. Node management, alarm, and timing terminations require a control card interconnect panel (CCIP). One CCIP serves both active and redundant integrated control cards. There are two variants of CCIP for US Telco (90-2295-x1) and International (90-2295-x2) requirements. This card is delivered with R5.0 software, a larger SanDisk and with an enhanced Processor Module (ePM).

INTEG CALLP/PNNI CARD-2 WITH EPM clei INTEG CALLP/PNNI CARD-2 WITH EPM

INTEG CALLP/PNNI/SPOOLING CARD-2 R5.0 This card provides the functionality of a Control Card-2, a CallP Card-2, a PNNI Card-2, and a Data Spooling-2 card, all combined on a single card. Two cards are required for redundancy per 7470 system. This card must be installed in Control CArd slots only, and cannot be used in systems that have also been configued with CallP-2 Cards or PNNI-2 Routing cards. Node management, alarm, and timing terminations required a control card interconnect panel (CCIP). One CCIP serves both active and redundant integrated control cards. There are two variants of CCIP for US Telco (90-2295-x1) and Internatinal (90-2295-x2) requirements. This card is delivered with R4.3 R5.0 software, a larger SanDisk and with an enhanced Processor Module (ePM).

INTEG CALLP/PNNI/SPOOLING CARD-2 W/EPM INTEG CALLP/PNNI/SPOOLING CARD-2 W/EPM

INV MULTIPLEX CARD IMC This assembly is a UCS resource card for inverse multiplexing applications. Based on the Bonding standard, the application supports n*64Kbit/s and n*56Kbit/s channels where n=15 for mode 1 and n=14 for mode 3 between 3600/45/64 nodes. Each IMC supports a total of 30 network-sidechannels (includes mode 3 monitor channels). Supoorted by Generic 1116 or greater.

IP SERVICE CARD (ISC) clei This card enables additional IP functionality on existing interfaces for the 7470 MSP. Release 4.3 of the ISC provides new capabilities in addition to those supported in R4.2. Dynamic routing using OSPF is supported 1+1 redundancy of ISCs is supported when installed in adjacent slots and with the use of a Dual Mau (90-6819-01). This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

IP SERVICES CARD (ISC) clei This card enables additional IP functionality on existing interfaces for the 7470 MSP. Release 4.3 of the ISC provides new capabilities in addition to those supported in R4.2. Dynamic routing using OSPF is supported. 1+1 redundancy of ISCs is supported when installed in adjacent slots and with the use of a Dual Mau (90-6819-01). This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

ISDN BRI 4 PORT CARD This card provides four Basic Rate Interface BRI interfaces for use at either the S or T reference points. This card is supported by Generic 1116 or greater.

ISDN BRI DIST PANEL ISDN Basic Rate Distribution Panel

ISDN BRI MODEM Daughter card used on the Dual 2.048 MBPS E1 Card (90-0565-01/08) for ISDN applications where conformance to interim CTR-4 layer one is required. This module is mutually exclusive with the Voice Compr ession Module (90-0566-01) and the Voice Compression Module-3 (90-0566-04). Supported by Generic 1116 or greater.

ISDN DUAL T1-2 CBL 6FT ISDN Dual T1-2 CBL 6FT.

ISDN FRAMING MOD Daughter card used on the Dual 2.048 MBPS E1 Card (90-0565-01/08) for ISDN applications where conformance to interim CTR-4 layer one is required. This module is mutually exclusive with the Voice Compr ession Module (90-0566-01) and the Voice Compression Module-3 (90-0566-04). Supported by Generic 1116 or greater.

ISDN S/T BRI CARD 4CCT This card provides four Basic Rate Interface BRI interfaces for use at either the S or T reference points. This card is supported by Generic 1116 or greater.

ISDN S/T BRI CARD 8CCT This card provides eight Basic Rate Interfaces (BRI) interfaces for use at either the S or T reference points. This card is supported by Generic 1116 or greater.

ISL 10M-DUPLEX CABLE This part contains the Up and Down ISL cabling required to interconnect a Dual Peripheral Shelf to the Switching Shelf, or one subunit of a High Speed Peripheral Shelf to the Switching Shelf. This part number is a multi-mode 10 meter duplex fiber cable with staggered ends. The part includes two dual ISLs, where each dual ISL consists of two bundled 800 Mb/s strands that together create an Up or Down ISL at 1.6 Gb/s.

ISL 10M-SIMPLEX CABLE This part contains the Up and Down ISL cabling required to interconnect a Low Speed Peripheral Shelf to the Switching Shelf. This part number is a multi-mode 10 meter single fiber cable with staggered ends. The part includes two ISL cables, where each ISL cable consists of an 800 Mb/s strand to create an Up or Down ISL.