E&M MODULE (+4/-10 DB) clei Single E&M module for termination of North American public network services such as UltraWATS, SDN, Megacom and VPN series offering TLP's of -3 to -10.5DB for receive and +4 to -3.5DB for transmit. Extended TLP'S are available in 4 wire mode; receive: +11 to +3.5DB, transmit: -12 to -19.5 DB. Module employs Type 1 or Type 2 signalling. This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

E&M MODULE (A-LAW) Single E&M module for general applications interfacing to European and International voice terminal equipment with TLP's for receive and transmit of +4.0 to -3.5 DB. Extended TLP'S are available in 4 wire mode; receive: +11 to +3.5DB, transmit: -12 to -19.5 DB, module employs Type 1 or Type 2 signaling. (Type 2 signaling is supported by a special wiring configuration that requires separate external 48VDC source).

E&M MODULE (TYPE 1) Single E&M module for end-to-end or corporate network connections interfacing to North American voice terminal equipment with TLP's for receive and transmit of +4.0 to -3.5DB. Extended TLP'S are available in 4 wire mode; receive: +11 to +3.5DB, transmit: -12 to -19.5 DB, module employs Type 1 or Type 2 signaling.

E&M MODULE (TYPE 5) Single E&M module for general applications interfacing to European and International voice terminal equipment with TLP's for receive and transmit of +8.5 DB to -7DB in 2W mode and -5 to -16 in 4W mode; module employs Type 5 signaling.

FXO (LGE) MODULE (+4/-10DB) clei Single FXO (LGE) module for termination of North American public network services such as UltraWATS, SDN, Megacom and VPN series offering TLP's of -3 to -10 DB for receive and +3 to -4 DB for transmit; module operates as FXO or DPT circuits. This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

FXO (LGE) MODULE (0/-7DB) Single FXO (LGE) module for end-to-end or corporate network connections interfacing to North American voice terminal equipment with TLP's for receive and transmit of 0 to -7 DB; module operates as FXO or DPT circuits.

FXS (LGS) MODULE (A-LAW) Single FXS (LGS) module for general applications interfacing to European and International voice terminal equipment with TLP's for receive and transmit of 0 to -7DB; module provides line reversal capability.

FXS (LGS) MODULE (LR) Single FXS (LGS) module for termination of North American public network services such as UltraWATS, SDN, Megacom and VPN series offering TLP's of -3 to -10DB for receive and +4 to -3DB for transmit; this module provides line reversal capability and increased loop performance. Module operates as FXS, PLAR or DPO circuits. Recommended for all new installations.

FXS (LGS) MODULE (UK) Single FXS (LGS) module for general applications interfacing to voice terminal equipment certified to connect to public networks in the United Kingdom; module provides line reversal and third-wire capability; does not apply to 3624 MainStreet. Offers TLP's of +1/-6 for receive and +4/-3 for transmit.

V.35 MODULE clei Single V.35 module providing for a single V.35 compatible interface (DTE or DCE) per module. Three control leads are supported; DCD/RTS/ALB when configured as DCE. These modules cannot be used to derive a clock for system synchronization. This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

V.35 PFRA DCM MODULE (PUBLIC FR ACCESS) Single V.35 module providing for a single V.35 compatible interface (DTE or DCE) per module. Three control leads are supported; DCD/RTS/ALB when configured as DCE. Both HCM and transparent speeds are supported up to 64KBPS, for speeds higher than 64KBPS refer to node documentation. These modules can be used to derive a clock for system synchronization. Enhanced for public frame relay access.<(><<)> p>NOTE: MUST NOT for USED in 3624 APPLICATIONS or damage will occur to the system itself.

.19 UDP RM BRKT Mounting bracket used for mounting two 3620 Distribution Panels (90-2255-01) or two 3612/24 Base Distribution Panels (90-2256-01) or one 3630 Base Distribution Panel (90-2257-01) into a 19 rackmount c onfiguration. Personality modules and Base Distribution Panels ordered separately.

3612 CONTROL CARD 4 Spare control card offering up to 2MB memory space. Supports Generic 3612 R5 S/W load or higher (90-0599-xx). Software Kit must be ordered separately (90-0599-xx).

3612 CPSS MODULE Allows CPSS operation over satellite links terminating on 3612 aggregate modules. All four aggregates can support satellite CPSS with this card installed. Mounts on control card, either 90-0576-02 o r 90-0576-05.

3612 E1 AGGREGATE-BNC WITH ADAPTOR PLATE This E1 Aggregate, with a 75 ohm BNC connector, takes up a single aggregate slot position within the 3612. It supports up to 8 circuits and can be used for either an aggregate connection or interfacing to a local PBX. Functionally identical to 90-2846-01 but includes internal cable and adaptor plate for use with Rack Mount 3612 (90-0575-68).

3612 E1 AGGREGATE-RJ45 WITH ADAPTOR PLAT This E1 Aggregate, with a 120 ohm RJ45 connector, takes up a single aggregate slot position within the 3612. It supports up to 8 circuits and can be used for either an aggregate connection or interfacing to a local PBX. Functionally identical to 90-2846-02 but includes internal cable and adaptor plate for use with Rack Mount 3612 (90-0575-68).

3612 E1 TRIB MOD (BNC) WITH ADAPTER Provides a E1 interface to a co-located PBX, video codec, bridge, router or data device. AQA(Activity Qualified Access) monitoring control is supported as a function by this module. Occupies one module position and is capable of running up to 15 DS0s connections to the aggregate. User interface is 75 ohm BNC.

3612 FRAME RELAY MOD R3.0 The FRM is a 15-port Frame Relay switch that occupies a single slot position within the 3612 and supports FR traffic at n*8k and super-rate speeds. Requires 3612 Release 8. This release introduces DLCI multiplexing.

3612 R8 100-240VAC SYSTEM Desktop, wall-mount, 19 rack-mount system accommodates up to four aggregates and twelve channel modules. Includes chassis, internal power supply(100-240VAC) with integral ringing generator(factory configured for 25Hz, use reconfigurable to 20Hz), Control Module 3 (90-0575-05),backplane, and the latest version of generic B218(90-0599-80). Optional slide assembly(90-9084-01), optional wall mount bracket(90-0338-04), and customer documentation(90-0582-08) to be ordered separately.

3612 R8 S/W KIT Set of five EPROMls containing the latest revision of software B218. Note: Cannot be used with control module 90-0576-01, 90-0576-02, or 90-0576-04. Can only be used with Control Card 90-0576-05.