This part is the field replaceable power supply for the Mainstreet family of IAD's. The power supply is for connecting to DC power in either 3612,3624, or 3630 rackmount, wallmount, desk top systems. The ringer is a seperate part.

This part is the field replaceable power supply for the Mainstreet family of IAD's. The power supply is for connecting to AC mains in either 3612, 3624, or 3630 rackmount, wallmount, desk top systems. The product comes with an integral ringer. The ringer frequency is selectable by a jumper to operate at either 20hz or 25hz.

GSLC-12 TDM SHDSL LINE CARD THE GSLC-12 IS A 12 PORT SHDSL LINE CARD. THIS LINE CARD IS DESIGNED TO BE INSTALLED IN THE 3600 MAINSTREET PRODUCT LINE. THE LINE CARD CAN CONNECT TO THE ALCATEL 3RD PARTY SHDSL NTU'S.

PWR SUPPLY 48/60VDC 3600 Mainstreet DC Power Supply (-48 TO 60VDC). This part provides DC power for the 3600 Mainstreet system and requires a power tray (90-3669-03) to connect to the system. The power supply can be used in pairs in load sharing mode to provide redundant power. This power supply is designed to replace (90-2378-02).

PWR SUPPLY -48/60VDC 3600 Mainstreet DC Power Supply (-48 TO 60VDC). This part provides DC power for the 3600 Mainstreet system and requires a power tray (90-3669-03) to connect to the system. The power supply can be used in pairs in load sharing mode to provide redundant power. This power supply is designed to replace (90-2378-02).

PWR SUPPLY 100-240VAC 3600 Mainstreet AC Power Supply (87 to 264VAC). This part provides AC power for the 3600 Mainstreet system and requires a power tray (90-3669-11 single feed, or 90-3669-12 dual feed) to connect to the system. The power supply can be used in pairs in load sharing mode to provide redundant power. This power supply is designed to replace (90-2378-01).

PWR SUPPLY ~230VAC 3600 Mainstreet AC Power Supply (87 to 264VAC). This part provides AC power for the 3600 Mainstreet system and requires a power tray (90-3669-11 single feed, or 90-3669-12 dual feed) to connect to the system. The power supply can be used in pairs in load sharing mode to provide redundant power. This power supply is designed to replace (90-2378-01).

96M CTL. INTEG. CTL & ISC SANDISK This part is the NAND-based 256M SanDisk used in R5.0 (and higher)Control and Integrated CallP/PNNI cards. Permanently held at LA status.

96M CTL. INTEG. CTL & ISC SANDISK This part is the NOR-based 256M SanDisk used in R4.3 Control and Integrated CallP/PNNI cards. Permanently held at LA status.

96M CTL. INTEG. CTL & ISC SANDISK This part is the NOR-based 96M SanDisk used in R4.2 (and lower) Control and Integrated CallP/PNNI cards, and in all IP Service cards. Permanently held at LA status. This kit can also be used to upgrade a 90-6184-01 ISC card to the 90-6184-12 ISC card level of functionality, and replaces the ISC Card upgrade kit, 90-7736-01.

DUAL E1 CARD 3 (120 OHM) G.703/G.704 This is the 120 ohm Dual E1 Card version 3. This card is backwards compatible with 90-0565-08 (Dual E1 2.048 Card)and 90-0568-02 (E1-120 OHM LIM MODULE). This card incorporates the LIMs on board so no external LIM is required. This card is designed to replace the existing Dual E1 card and has been designed to simplify ordering and sparing.

DUAL E1 CARD 3 (120 OHM) This is the 120 ohm Dual E1 Card version 3. This card is backwards compatible with 90-0565-08 (Dual E1 2.048 Card)and 90-0568-02 (E1-120 OHM LIM MODULE). This card incorporates the LIMs on board so no external LIM is required. This card is designed to replace the existing Dual E1 card and has been designed to simplify ordering and sparing.

DUAL E1 CARD 3 (75 OHM) This is the 75 ohm Dual E1 Card version 3. This card is backwards compatible with 90-0565-01 (Dual E1 2.048 Card)and 90-0568-01 (E1-75 OHM LIM MODULE). This card incorporates the LIMs on board so no external LIM is required. This card is designed to replace the existing Dual E1 card and has been designed to simplify ordering and sparing.

H/S PERIPHERAL SHELF FRONT COVER The High Speed Peripheral Shelf front cover is an optional assembly for the High Speed Peripheral Shelf (90-2291-01). It is required for European Union EMC Class B compliance. (Note that Class B compliance is normally required for locations which are other than telecommunications centre ; if the location is a telecommunications centre, then the HSPS front cover may not be required.) The H/S Peripheral Shelf front cover is field installable, and the kit consists of mounting brackets, shelf cover and instructions for installation. The cover is perforated to allow all LEDs to be visible through the perforations. Locking clips at the top of the cover allow the cover to be removed to enable access to the OC12 line cards and FICs.

R6.0 CTL TO INTEGRATED CTL CONVERT KIT The Control to Integrated Control conversion kit is used to convert a Control card to an Integrated Control card, enabling the card to perform the PNNI and Call Processing functions provided by PNNI and CallP cards in a common Control mode system. The kit contains part number labels, password to enable the conversion and instructions for installation. The software required for the conversion is part of the standard release load.

R5.0 CTL TO INTEGRATED CTL CONVERT KIT The Control to Integrated Control conversion kit is used to convert a Control card to an Integrated Control card, enabling the card to perform the PNNI and Call Processing functions provided by PNNI and CallP cards in a common Control mode system. The kit contains part number labels, password to enable the conversion and instructions for installation. The software required for the conversion is part of the standard release load.

R4.3 CTL TO INTEGRATED CTL CONVERT KIT The Control to Integrated Control conversion kit is used to convert a Control card to an Integrated Control card, enabling the card to perform the PNNI and Call Processing functions provided by PNNI and CallP cards in a common Control mode system. The kit contains part number labels, password to enable the conversion and instructions for installation. The software required for the conversion is part of the standard release load.

MAINSTREET S/W MAINTENANCE UNIT This 90- level part number is used in conjunction with S/W maintenance contracts to calculate and order s/w for the nodes within a network over the period of the contract.

SMZ TO BNC 75OHM CABLE - 4P OC3/STM1 ELE This cable is used to connect the quad OC3/STM1 Electrical CR card to a patch panel at the rear of the cabinet.

SGL MODE SC-SC FIBER - 4P 0C3/STM1 IR-LR This cable is used to connect the quad OC3/STM1 MMF optical CR card to a patch panel at the rear of the cabinet.