OCU-DP CHANNEL UNIT-2 clei The OCU-DP Channel Unit provides an interface to the 3600/3645 system and 4 wire special service data circuits. DDSI/II compatible. Error correction and secondary channel. Data rates of 2.4, 4.8, 9.6, 19.2 and 56 kb/s. Min 40dB insertion loss. Requires 3600 equipped with Common Carrier card (90-1234-01). This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

OCU-DP CHANNEL UNIT-2 The OCU-DP Channel Unit provides an interface to the 3600/3645 system and 4 wire special service data circuits. DDSI/II compatible. Error correction and secondary channel. Data rates of 2.4, 4.8, 9.6, 19.2 and 56 kb/s. Min 40dB insertion loss. Requires 3600 equipped with Common Carrier card (90-1234-01). This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

OCU-DP CHNL UNIT-2 QCTL This product is used with the 3600 and 3600+ Mainstreet. The OCU-DP channel unit provides a special service data circuit for the 3600 Mainstreet. DDS I and II compatible. Error correction and secondary channel. Data rates of 2.4, 4.8, 9.6, 19.2, and 56kbs.

One per system required for DDS DS0A rate adaption of data channels connected over 275x MainStreet Data Termination Units; OCU modules (90-0693-01) do not require this module; module also generates ringback tone for Megacom800 applications; module is mutually exclusive with the Tone module (90-0512-01 and 90-0512-02) and any DSP module.

PE FR R3&X.25 R1.2 A 3600/3600+ UCS card that functions as an integrated mulitprocessor, high performance frame relay and/or X.25 switch. Supports either frame relay or X.25 protocols, or both concurrently, depending on network and customer requirements. A total of 3.968 Mbps (2 x 1.984 Mb/s) of bandwidth is available between the card and the switching matrix. The card supports an interface to the FASTbus via the FIP (90-1637-01). The PE card is optimized for X.25 and supports up to 512 logical X.25 user ports per card. Minimum node software release of 6.1 is required. Requires a fan tray to operate. Maximum three PE cards per 3600 shelf.

PERIPHERAL SHELF 2 R3.1 clei The R3.1 Peripheral Shelf Cardfile is a 19 rackmount shelf which has 12 universal card slots (UCS) and 2 common equipment card slots (X and Y). The X (and Y if redundant fabric is required) common equipment card slot is equipped with a Dual Hub or SHUB Card. The 12 UCSs are equipped with 0, 1, or 2 Control Cards and up to 10, 11, or 12 interface cards depending on the number of Control Cards installed. One Control Card is installed for non-redundant control, two for control redundancy, and zero if Control Cards have already been installed in another Peripheral Shelf of the 36170 system. A 36170 system can be equipped with up to 8 Peripheral Shelf Cardfiles for a total of 96 UCS's. This high power peripheral shelf increases the power handling capacity to allow for higher-powered cards in future releases of the 36170. This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

PNNI ROUTING CARD-2 R4.3 This is a UCS card that provides switched services PNNI dynamic routing. THis card or an Integrated CallP/PNNI Card-2 are required for systems that use PNNI Routing. This card is delivered with R4.3 software.

PRI 8P RJ45 D.PNL CABLE This 1 meter cable connects a 7470 T1 PRI UFR OCTAL (90-2541-X1) E1 120 PRI UFR OCT(90-2541-X2)T1 CR ATM CARD (90-4671-X1)E1 CR 120 ATM CARD(90-4671-X2)T1 CE 8 PORT (90-2517-X1) or E1 CE 120 8 PORT(90-2517-X2) to a PRI RJ45 D.PNL (90-2543-X1) .

PRI BNC DISTRIBUTION PANEL The PRI Coax Distribution Panel provides 8 external BNC interfaces to the 75 ohm E1 coaxial ports of a PRI card. It may be used with any of the PRI cards (90-2541-x3 or 90-2544-x3). A D.78 cable connects the PRI card to the panel which provides a BNC connector for each port TX and one for each port RX. The panel is a 1 vertical unit (VU) high rack-mountable device. Grounding switches allow the service personnel to independantly ground any of the coaxial shields. This panel is shipped with 1VU mid-mount brackets.

PRI FACEMOUNT BNC D.PNL The PRI Coax Distribution Panel provides 8 front mounted external BNC interfaces to the 75 ohm E1 coaxial ports of a PRI card. It may be used with any of the PRI cards (90-2541-x3 or 90-2544-x3). A D.78 cable connects the PRI card to the panel which provides a BNC connector for each port TX and one for each port RX. The panel is a 1 vertical unit (VU) high rack-mountable device. Grounding switches allow the service personnel to independantly ground any of the coaxial shields. This panel is shipped with 1VU mid-mount brackets. With the exception of offering front mounted BNC connectors, this assembly is identical to the 90-2543-02 .

PRI RJ45 DIST PANEL ISDN Primary Rate Distribution Panel

PRI RJ45 DISTRIBUTION PANEL The PRI RJ45 Distribution Panel provides 8 external RJ45 interfaces to the 100 ohm T1 or 120 ohm E1 twisted pair ports of a PRI card. It may be used with PRI cards 90-4671-x1/x2, 90-2541-x1/x2, 90-2517-x1, 90-2544-x1/x2, and 90-7277-xx. The panel is a 1 vertical unit (VU) high rack-mountable device. For PRI CE cards (90-2517-x2), use the 90-5930-x1 E1 RJ45 ISDN D.PNL. This panel is shipped with 1VU mid-mount brackets.

PSI 16 PORT FR I/O CARD The programmable serial interface (PSI) I/O card provides 16 ports configurable as V.35, X.21 or V.28/RS-232 physical interfaces. The physical interface is a 26-pin SCSI D-shell, so appropriate adapter cables must be used for V.28, V.35 or X.21. Ref 90-6502-01..-04, 90-7004-01..-04, 90-7005-01..-04

PSU 110-220V ADSL DTU

PWR ADPT. 115VAC

PWR SUPPLY -48/60VDC 3600 Mainstreet DC Power Supply (-48 TO 60VDC). This part provides DC power for the 3600 Mainstreet system and requires a power tray (90-3669-03) to connect to the system. The power supply can be used in pairs in load sharing mode to provide redundant power. This power supply is designed to replace (90-2378-02).

PWR SUPPLY 100-240VAC 3600 Mainstreet AC Power Supply (87 to 264VAC). This part provides AC power for the 3600 Mainstreet system and requires a power tray (90-3669-11 single feed, or 90-3669-12 dual feed) to connect to the system. The power supply can be used in pairs in load sharing mode to provide redundant power. This power supply is designed to replace (90-2378-01).

PWR SUPPLY 48/60VDC 3600 Mainstreet DC Power Supply (-48 TO 60VDC). This part provides DC power for the 3600 Mainstreet system and requires a power tray (90-3669-03) to connect to the system. The power supply can be used in pairs in load sharing mode to provide redundant power. This power supply is designed to replace (90-2378-02).

PWR SUPPLY 87/264VAC

PWR SUPPLY ~230VAC 3600 Mainstreet AC Power Supply (87 to 264VAC). This part provides AC power for the 3600 Mainstreet system and requires a power tray (90-3669-11 single feed, or 90-3669-12 dual feed) to connect to the system. The power supply can be used in pairs in load sharing mode to provide redundant power. This power supply is designed to replace (90-2378-01).