UPG KIT INTEG/EPM TO INTEG. W/SPOOLING This kit is used to upgrade a 7470 Release 4.3-5.0 Integrated CallP or Integrated CallP/PNNI card, or 7270 Release 5.0 control card to an Integrated CallP/PNNI/Spooling card in Release 5.0. Also it is to be used to upgrade a R2.0 7670 ESE ECC (90-8396-01) to support integrated data spooling.Factory shipments of R5.0 Integrated CallP/PNNI/Spooling cards ship with the SRAM included and do not require this upgrade kit. The kit contains a 6M SRAM card, part number labels and instructions for installation. Note for the 7470 that if the card to be upgraded does not use the ePM and larger (256M) SanDisk, then the Integrated CallP or Integrated CallP/PNNI Upgrade to Integrated CallP/PNNI/Data Spooling Kit(90-8977-01) should be used instead. Note for the 7270 that if the card to be upgraded does not use the ePM and larger (96M) SanDisk, then both the 7270 control card upgrade kit (90-4452-13) and this upgrade kit are required..

UPG KIT INTEG/EPM TO INTEG. W/SPOOLING This kit is used to upgrade a 7470 Release 4.3-5.0 Integrated CallP or Integrated CallP/PNNI card, or 7270 Release 5.0 control card to an Integrated CallP/PNNI/Spooling card in Release 5.0. Also it is to be used to upgrade a R2.0 7670 ESE ECC (90-8396-01) to support integrated data spooling.Factory shipments of R5.0 Integrated CallP/PNNI/Spooling cards ship with the SRAM included and do not require this upgrade kit. The kit contains a 6M SRAM card, part number labels and instructions for installation. Note for the 7470 that if the card to be upgraded does not use the ePM and larger (256M) SanDisk, then the Integrated CallP or Integrated CallP/PNNI Upgrade to Integrated CallP/PNNI/Data Spooling Kit(90-8977-01) should be used instead. Note for the 7270 that if the card to be upgraded does not use the ePM and larger (96M) SanDisk, then both the 7270 control card upgrade kit (90-4452-13) and this upgrade kit are required..

V.24/RS232 SYNC/ASYNC DCC ( 6 CCT ) CARD This card consists of 6 individual RS232/CCITT V.24 compatible interfaces. Three of the interfaces are available from the backplane with the remaining three available at the front panel 25 pair connector (AMP CHAMP).

V.28 SUBD26M-DB25F DCE CABLE 3M. This cable is for use with the Programmable Serial Interface I/O card.

V.28 SUBD26M-DB25F DTE CABLE 3M. This cable is for use with the Programmable Serial Interface I/O card.

V.28 SUBD26M-DB25M DCE CABLE 3M. This cable is for use with the Programmable Serial Interface I/O card.

V.28 SUBD26M-DB25M DTE CABLE 3M. This cable is for use with the Programmable Serial Interface I/O card.

V.35 2703 DTU

V.35 CARD (3 CCT)

V.35 CARD (6 CCT) This card offers six CCITT V.35 interfaces. Three of the circuits are available at the backplane connector and three others are available on the card's faceplate connector (AMP CHAMP). This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

V.35 DIST PANEL (DB25) (EU-TC AND OTHER) V.35 Distribution panel comes complete with shielded AMP Champ cable and DB25 connectors, for installation in other environments including Telecom Centres.

V.35 DIST PANEL (M34) (EU-TC AND OTHER) Mainstreet V.35 Distribution panel comes complete with shielded AMP Champ cable and M34 connectorsm, for installation in other environments including Telecom Centres.

V.35 DIST PANEL 19 inch rack mountable assembly which provides backplane access to six V.35 circuits via six DB-25 connectors. Included are two 25 pair cables required to connect the distribution panel to the system.

V.35 DIST PNL 19 inch rack mountable assembly which provides backplane access to six V.35 circuits via six DB-25 connectors. Included are two 25 pair cables required to connect the distribution panel to the system.

V.35 DIST. PANEL M34-36

V.35 ISDN 1603

V.35 MM DCE CABLE (DB25M-M34M)(3M)

V.35 MODULE (HCM2)

V.35 PRI CARD (56 KB) clei This card presents a 56 kbps V.35 interface. Supported by Generic 1114 or above. Based on the (90-0669-01) V.35 PRI Card platform. This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

V.35 PRI CARD This card presents a 30 channel, V.35 interface. Allows for faceplate (DB-25) or backplane (50 pin Champ) access. Configured as a Data Termination Unit (DTE). Supported bit rates are from 64 Kbps to 1920 Kbps. This card is supported by Generic 1113 or greater, and also offers reduced framing overhead allowing for additional HCM data. For use with V.35 DB25M-M34M DCE Cables (90-0360-0X).