QUAD STM1 ELEC UNI/NNI clei The quad OC3/STM1 Electrical UNI/NNI Card is a ATM interface card operating at the SONET OC3 rate of 155 Mbps per port. The electrical interface is dual coaxial BNC connectors, with a range of 450 feet. The line code is code mark inversion (CMI). The quad OC3 card is compliant to the requirements of the ATM Forum UNI Specification (Version 3.1) and the ATM Forum B-ICI Specification (Version 2.0). This card is also supported in ESE R2.0.

R4.3 CTL & INTEG. CALLP/PNNI UPGRADE KIT This kit is used to upgrade an R4.3 Control or Integrated CallP/PNNI card to the enhanced Processor Module(ePM) and larger NOR Based (256M) memory card. Factory shipments of R4.3 Control and Integrated CallP/PNNI cards ship with the ePM installed, and with the larger memory card included, and do not require this upgrade kit. The kit contains an ePM (333 MHz PowerPC 755 module with 512M RAM), 256M memory card, part number labels, and instructions for installation. Note: The NOR-Based memory card is replaced by a NAND-based memory card for later loadsets of R4.3. Be aware that this part supplies the older NOR based memory card and that you should check with Product Management before ordering this part. Field Notice FN1867 provides more details.

R4.3 CTL TO INTEGRATED CTL CONVERT KIT The Control to Integrated Control conversion kit is used to convert a Control card to an Integrated Control card, enabling the card to perform the PNNI and Call Processing functions provided by PNNI and CallP cards in a common Control mode system. The kit contains part number labels, password to enable the conversion and instructions for installation. The software required for the conversion is part of the standard release load.

R5.0 CTL & INTEG. CALLP/PNNI UPGRADE KIT This kit is used to upgrade an R5.0(or higher) Control or Integrated CallP/PNNI card to the enhanced Processor Module(ePM) and larger(256M) SanDisk. Factory shipments of R5.0 Control and Integrated CallP/PNNI cards ship with the ePM installed, and with the larger SanDisk included, and do not require this upgrade kit. The kit contains an ePM (333 MHz PowerPC 755 module with 512M RAM), 256M SanDisk, part number labels and instructions for installation.

R5.0 CTL TO INTEGRATED CTL CONVERT KIT The Control to Integrated Control conversion kit is used to convert a Control card to an Integrated Control card, enabling the card to perform the PNNI and Call Processing functions provided by PNNI and CallP cards in a common Control mode system. The kit contains part number labels, password to enable the conversion and instructions for installation. The software required for the conversion is part of the standard release load.

R5.0 SERVICE CARD-2 UPGRADE KIT This kit is used to upgrade an R5.0(or higher) Service Card-2 (CallP,PNNI or Data Spooling card) to the enhanced Processor Module (ePM). Factory shipments of R5.0 Service Card-2 and higher cards ship with the ePM installed and do not require this upgrade kit. The kit contains an ePM(333 MHz PowerPC 755 module with 512M RAM), part number labels and instructions for installation.

R6.0 CTL TO INTEGRATED CTL CONVERT KIT The Control to Integrated Control conversion kit is used to convert a Control card to an Integrated Control card, enabling the card to perform the PNNI and Call Processing functions provided by PNNI and CallP cards in a common Control mode system. The kit contains part number labels, password to enable the conversion and instructions for installation. The software required for the conversion is part of the standard release load.

REDUND SW SHELF CBL EMC Identical to 90-0697-01-01 but tailored for EMC Class B applications.

REDUND SW SHELF CBL This cable assembly is required when configuring redundant Switching Shelves. Included is one cable assembly (4 ft).

REDUNDANT SWITCHING SHELF CABLE (EMC) Identical to 90-0697-01-01 but tailored for EMC Class B applications.

RS-422 DCC BUFFER MODULE Optional module for use with RS422 DCC (4CCT) P/N 90-1549-01. Provides programmable slip buffers operating on a per port basis.

RS232 DIST PANEL (EU-TC AND OTHER) Mainstreet RS232 Distribution panel comes complete with shielded AMP Champ cable, for installation in other environments including Telecom Centres.

RS232 DIST PANEL 19 inch rack mountable assembly which provides backplane access to six RS-232 circuits via six DB-25 connectors. Included are two 25 pair cables required to connect the distribution panel to the system.

RS232 DIST PNL.

RS232 DIST PNL. 19 inch rack mountable assembly which provides backplane access to six RS-232 circuits via six DB-25 connectors. Included are two 25 pair cables required to connect the distribution panel to the system.

RS232 SYNC/ASYNC DCC(6) This card consists of 6 individual RS232/CCITT V.24 compatible interfaces. Three of the interfaces are available from the backplane with the remaining three available at the front panel 25 pair connector (AMP CHAMP).

RS232/V,24 MODULE CLEI Single RS232 module providing for dual RS-232/V.24 interfaces per module. Most common synchronous and asynchronous speeds are supported up to 64KBPS. Both HCM and transparent framing formats are supported. This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

RS232/V.24 MODULE clei Single RS232 module providing for dual RS-232/V.24 interfaces per module. Most common synchronous and asynchronous speeds are supported up to 64KBPS. Both HCM and transparent framing formats are supported. This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

RS422 DCC (4 CCT) This assembly consists of four RS-422/CCITT V.11 interfaces, each independently programmable for V.35, X.21, V.36, RS-449 or RS-530. Individual circuit clocking for data rates of 1200 b/s to 1920 kb/s is provided by this assembly. This part is supported by Generic 1115 or greater.

RS422 DCC 4CCTE MODULE This assembly consists of four RS-422/CCITT V.11 interfaces, each independently programmable for V.35, X.21, V.36, RS-449 or RS-530. Individual circuit clocking for data rates of 1200 b/s to 1920 kb/s is provided by this assembly. This part is supported by Generic 1115 or greater.